The 8 Best Folding Sawhorses of 2026

Pull one lever at each end and the legs fall into place. Bora's 1.6-second claim is the kind of number that usually evaporates in a driveway, and this one mostly holds up. There is no sequence to learn either: fold one leg back and the other does not care, which is the part that saves you at the end of a job when the truck is already running. Set up and tear down more than once a day and this is the pair that pays you back.

Each stand is rated to 1,800 pounds, and the working height lands at 30 inches with a longer pre-drilled metal top than most. That extra length is what you notice when you are laying a rail across and want bearing surface at both ends rather than a two-inch landing pad.

Bulk is the cost. At 46.5 inches long it wants a wall or a truck bed rather than a shelf, and moving both at once is a two-trip job. The steel that makes the pair sit still under a saw is the same steel you are carrying, and that is a bargain most people working alone will take.

Thirty-nine pounds for the pair is what you notice lifting the box, and the reason shows up the first time you set them on ground that is not level: the legs adjust independently from 26 to 32 inches in one-inch steps, so a corner can drop into a dip instead of being shimmed.

The steel is rated at 1,500 pounds per stand and 3,000 for the pair, and the beam top takes wood support arms for building a jobsite table. A carry handle on each frame is what makes moving one at a time practical rather than a two-handed waddle.

This is the pair for a sloped driveway or for work you want lower than 30 inches, since the 26-inch setting brings a heavy slab closer to the floor when you are loading it alone. The weight is the honest cost: carrying one is fine, carrying two across a yard is a chore. Check that both leg clips click before you load the top, because a clip that lets go takes the leg with it.

Where the Workhorse X gives you a fixed top and holes drilled in set places, the ToughBuilt C550 adds 2x4 arms that adjust, so a rail sits where the work needs it rather than where the holes happen to be. Capacity is 2,200 pounds for the pair, the frame is powder-coated steel with zinc-plated hardware, and the feet are shaped to sit on dirt as happily as on a slab.

We think of this as the table half of the category: two rails across the arms, a sheet of plywood on top, and you have a cutting surface that comes apart and rides in the truck. The adjustable arms are what makes that worth doing, since you set them once for a frame and they hold. It is the pair to take when the job needs a table rather than two supports.

It carries less than the Workhorse X for more money, so it earns its place on the arms and the finish rather than on raw numbers. If you are cutting sheet goods on a frame, that is a fair trade. If you mostly need two solid supports and somewhere to set a board, take the Bora and put the difference toward clamps.

This is the least expensive route here to a full 2,200-pound pair, and the price does not show up in the frame: steel throughout, non-slip treatment on the top and the feet, and four cast steel hooks for 2x4s that mount on the sides. It arrives assembled, so you fold the legs out and work.

For a pair that folds away behind a shelf, it does more than the job asks. The hooks let you frame a table if you want one, the legs lock in place without pins to line up, and the top has enough grip that a board stays put while you mark it.

Two things to know. The finish is the weak point, since steel left out in the rain shows surface rust at the joints, so plan on storing it under cover. And the 2x4 hooks are separate pieces you bolt on, which means they can walk off between jobs unless you leave them attached.

Neither is a reason to skip it. As a second pair for a truck, a rental property, or a first workbench, the WORKESS is the one that leaves money for lumber.

Folded, one of these is 3.67 inches wide and about 31 inches long, thin enough to stand in a garage corner or slide behind a door, and at 5.7 pounds light enough to carry in one hand with a board under the other arm.

The rating is 1,000 pounds per pair, the top has anti-slip rubber pads, and side latches clip two units together into a single bundle. That last detail is what makes them work as a pair rather than as two loose stands you chase around the garage.

Two is the plan, since CRAFTSMAN sells them one at a time. Bought as a pair it is the cheapest route here to a competent set, and the one we point people toward for painting, staining, and light cutting. What you give up is mass, because a stand that takes a bump from a hip will move, so set them where you will not be walking into them. On a flat garage floor, that is plenty.

Ours went up in a garage in about the time it takes to unfold two camp chairs: no assembly, no pins to line up, just pull the legs apart and drop the locking braces into place. That ease is the whole pitch, and with 900 pounds across both stands it is built for home projects rather than framing. For painting, staining, and weekend cuts, it is enough.

The details are more thoughtful than we expected from a house brand. Four top hooks and two bottom hooks per stand hold cords and locate a 2x4, and a fold-out stopper on each side becomes a shallow shelf where the driver, the pencil, and the coffee end up. Folded, they take about the depth of a stepladder and carry one-handed.

What they will not do is grow with you. The frame is metal but the fittings are plastic, and the 900-pound pair rating is the lowest in this group, so a sheet of plywood is fine while a stack of 2x10s is not. That is not a fault at this weight class; it is the boundary of what the pair is for.

The 2x4 holders on the WK-MPP are separate cast-steel pieces that clip onto the sides rather than fixed brackets, and they work loose in handling. That is the one detail we do not like: the capacity is real, but the hardware that turns the pair into a table is the least secure part of the design.

What it does bring is a press-button release, so one finger opens both legs, plus flip-down support legs that let you stand a board on edge while you work along it. The pair is rated to 2,600 pounds, just under the top pick, and the working height is 29.7 inches.

Set against the Workhorse X it is a little less capacity for a little more money, so it earns its place on the release and those flip-down legs rather than on the numbers. The legs are the real difference: with them down you can stand a sheet on edge and work along the top without a second person holding it.

Buy it when one-finger setup and a board stood on edge matter more than a fixed bracket top, and take the Workhorse X when the table itself is the point. For a shop where the pair stays put and the work comes to them, this one is easy to live with.